EARTHING AND LIGHTNING PROTECTION

Copper Coated earth Rod

Copper Coated Earth Ros offer installer the most economical method of achieving a low earth resistance.
Each rod has a high tensile strength, low carbon steel core.
99.95% pure copper is applied electrolytically and forms metallurgical bond between the steel core and the copper.
this combination makes the rod ideal for deep driving whilst also provides lasting resistance to corrosion.
The threads are formed by a cold rolling process which ensures strength and maintains the molecularly bonded copper covering along the full length of the threads.
cold rolled threads are stronger than cut-threads.
The standard copper thickness is 0.254 mm.
Greater copper thicknesses are also available.

Material: Pure Copper molecularly bonded onto steel core.

Threaded Coupling Dwel

These high-strength coupling are used for joining copper bond threaded earth rods together.
They facilitate deep driving and ensure continual contact between the rods both during and after installation.
The coupling also protects the earth rod threads during the installation with the driving head.
All coupling is manufactured from a high copper content alloy ensuring excellent corrosion resistance.

Material: Bronze.

Threaded Driving Head

These re-usable threaded driving heads are suitable for driving earth rods by hand or with a power hammer.
The Driving head Screws into the threaded coupling to allow deep driving of the earth rods.

Material: high tensile steel.

Threaded Driving Tip

Used at the initial Earthing rod to Provide more sharp edge to the earth rod to make it easy to drive into the ground without any corrosion to earth rod

Material: high tensile steel.

Solid Copper Earthing Rod

They are one of the best choices for Earth Electrodes. They can be used in areas with high corrosion or in applications where an exceptionally long life is needed. They are also used in installations with high fault currents. These Solid Copper Rods are manufacturing from Solid Copper bars and are then processed to enable jointing. These Solid Copper Rods however are not suitable for deep driving into the ground because of the possibility of bending.

Galvanized Steel Earthing Rod

These rods are made up of high strength low carbon steel and hot-dip galvanized. These are the lowest cost rods but also have the lowest corrosion resistance and low electrical conductivity and current carrying capacity

G - Clamp

These Clamps are used for joining earth rods to different sizes of stranded copper conductor. The Clamps have a high resistance to corrosion and are mechanically strong to ensure a lasting connection.

Material: gunmetal with M10x25 mm set screw.

U- Bolt Clamp [ GUV ] Type

This Versatile range of bolt clamps can be used to connect flat tapes and stranded cables to earth rods, reinforcing bars (re-bar), hand rails so on.

Material: gunmetal or Brass

U- Bolt Clamp [ E ] Type

Hight Strength Copper Alloy U- bolt Clamp designed to provide a high-quality low resistance connection between flat tape or stranded conductor and earth rod or rebar. ” U ” bolt Threaded M10 

Material: gunmetal or Brass. Plate with M10 Threaded ” U ” Bolt

One Hole Cable Clip

The One-hole cable clips provide an easy method of fixing stranded copper conductors to surface.

Available Materials: Copper & Copper Clad Steel & Steel & H.D.G Steel.

Metallic Cable Clip

The Metallic cable clips secure the stranded copper conductor to the building surface

available Materials: Copper & Copper Clad Steel & Steel & H.D.G Steel 

DC Cable Clip

The DC cable clips secure the stranded copper conductor to the building surface

available Materials: Brass

Tape Clip

Tape clips hold the flat tape conductor flush to the building surface
These metal Tape Clips hold the Tape flush to the surface and fixed using two screws 


available Materials: Copper & Copper Clad Steel & Steel & H.D.G Steel

DC Tape Clip

Metallic DC Clips secure the flat tape conductor to the building surface.
Fix using countersunk woodscrew.

available Materials: Bronze.

Square Tape Clamp

Four-way Connectors are suitable for making cross, straight through or Tee joints in flat tape. The base has a counter sunk hole in the middle for securing the clamp to the building surface and lid fixed by means of four screws, fix using 1 1/2″ x No.10 and No.10 wall plug.

available Materials: Brass

Square Conductor Clamp

Four-way connectors are suitable for making cross, straight through or tee joints in Stranded Copper Conductors

available Materials: Brass

Square Conductor to Tape Clamp

Four-way connectors are suitable for making crossing over flat tape and conductors.

available Materials: Brass

T P X Clamp

  • Suitable to connect rod to flat conductor (Without intermediate Plate)

  • Suitable to connect cross conductor with shown range in blew table

Available material: H.D.G Steel

Test Clamp

It is used to form a disconnecting joint between the down conductor system and the Earthing system.
Simple to install, provide an effective Low resistance overlap connection between stranded cables and copper tapes.

Material: High quality Copper alloy.

Oblong Test Clamp

Oblong test clamps are used to join conductor tape to facilitate in the annual testing of the lightning protection system.

Material: High quality Copper alloy.

Cable Test Clamp

Test Clamp are manufactured from copper, it is used to form a disconnecting joint between the down conductor system and the Earthing system.

Material: High quality Copper alloy.

C - Clamp

C clamp or pure copper C clamp is used as a wire or cable joint, made of copper material with low resistivity, good electrical conductivity, good corrosion resistance, and convenient installation.

available Materials: Copper & Tinned Copper.

Flexible Flat Copper Connector [ Braid ]

Flexible braids are manufactured from electrolytic copper. wire. Braids of different conductor sizes or lengths are available on request. Standard finish – bright copper Flexible braids can be supplied tin plated.

Flexible Circular Copper Connector [ Braid ]

Flexible braids are manufactured from electrolytic copper. wire. Braids of different conductor sizes or lengths are available on request. Standard finish – bright copper Flexible braids can be supplied tin plated.

Earthbar [ Test Link ]

Earth bars are available in a variety of sizes and specifications.
Our Standard earth bars are shown in the tables below.

Material:       Bar: 50x6mm hard drawn copper       
                      Base: Plastic
                      Fittings: M10 Hexagon head set screws,               
                                      Nuts & Washers.

Terminal Lug 1 Hole A

Terminal Lugs are designed to permit connection to a terminal. They can often be easily mounted to any post, stud or chassis and come in a wide variety of shapes and sizes

 

Terminal Lug 1 Hole B

Cable terminals are manufactured from high conductivity seamless copper tube 

All terminals are annealed to avoid cracking and splitting when crimped and electro-tin plated to combine maximum electrical conductivity with mechanical strength.

  • Supplied with bolts, washer, and nuts.

  • DIN EN 13600

Terminal Lug 2 Holes

  • 2 Holes heavy duty lugs are best Suited in application where two bolts are needed to avoid rotation or movement of the lugs.

  • They are used for heavy duty industrial application requiring mechanical strength

  • Tin Plated Copper Lugs to Improve electrical conductivity and avoid oxidation of copper

  • Chamfered mouth for easy cable insertion

  • Can be with / without inspection window.

  • Supplied with Bolts, Washer, and nuts.

Bi-metallic Terminal Lug

Tube: Seamless, one-piece tube           Material: Pure Aluminum 99.5 %
Finish: Chemically treatment                Ring Material: High purity 99.9 % E.T.P copper
Ring Finish: Plain copper                       Tube Manufacturing: According to DIN EN 755-7.
Manufacturing: Copper ring is inserted in the Al palm and excellent connection is assured.
Bi-metallic insert (ring) lugs assure a maximum reliability connection of aluminum cables to copper busbars, copper bushings, etc.

Galvanized Steel Terminal Lug

  • Terminal Lugs are designed to permit connection to a terminal. They can often be easily mounted to any post, stud or chassis and come in a wide variety of shapes and sizes
    * Used with H.D.G Steel Wires.
    * ASTM 123/A 123M – 02

Air Terminal Rod

These air rods are used as a part of lightning protection system.The air rods are made from electrolytic grade copper, one side tapper pointed and the other side with suitable threads for fixing to air termination bases.

 

Air Terminal Rod Base

  • Air Terminal Rod Bases are used to support

    air rods on Flat roof surfaces.

Air Terminal MAST [ Stand ]

Fixed at roof top on concrete to provide more length to air termination.

Bare Copper Conductor

PVC Insulated Copper Cables

Copper Bars

Copper Tape

EL-Hamd Welding

It is a new Process Used for Welding the Copper conductor of the earthing net introduced by EL-Hamd Company.

Process Steps:

1. Set up the mold.
2. Pour the copper into the mold.
3. Wait few minutes till the Copper become cold.
4. Smash the mold with Hammer.
5. The Casting Weld Point is ready.

Thermo Welding

Earthing Pit

These are Suitable for most of Earthing & Lightning Protection Installations.Inspection Pit is Manufactured from Concrete. The Housing cage have an internal earth bar fitted diagonally across in slots provided in the base.

Earth bar

These earth bar fit into the slots provided in the concrete inspection housing and are used when multipe connections to earth rod are required.

Manufactured from pure copper.